Team Associated SC10 4×4 Kit Review

Hot New Release: Team Associated SC10 4×4

Feb 02, 2011 13 Comments by

NEW VIDEOS ADDED! Team Associated has finally made it official. The SC10 4×4 has been unveiled. While this 4WD short course truck has been highly anticipated, most people suspected a vehicle based on Associated’s 1/10-scale B44.1 4WD buggy or possible a smaller version of the 1/8-scale SC8 short course truck. Many Associated fans have even created homespun versions by using a RC8 chassis plate with a SC8. Contrary to all of the speculation, Associated has pulled the cover a whole new design for a whole new platform. The SC10 4×4 is not what anyone expected. Check it out:


Belt Drive
Associated designed the SC10 4×4 around a lightweight, low-drag belt driven system. The belt itself is thick and durable, measuring 5mm wide with 211 teeth. Due to the layout, the belt drives the front drivetrain only, while a standard 3-gear gearbox drives the rear end. Associaed states the belt drive works delivers explosive acceleration and yields a compact chassis layout, and reduced drivetrain friction. The belt also allows it to use 32-pitch gears with large teeth.

Decoupled Slipper
The unique “decoupled slipper” uses an internal thrust bearing assembly to allow the truck to feel like it has a slipper and center differential. There is no center differential. The top shaft connects the slipper unit to the front drive belt and the rear gearbox. The decoupled slipper allows the front and rear tires to slip independently, offering increased traction and stability. Without this feature, the slipper would slip and cause all four wheels to lose drive power.

Front Clicker
Instead of a standard front differential, Associated went with a front one-way “clicker” installed between the drive belt and front diff.  When loosened for high-traction tracks, the clicker locks up under acceleration but freewheels and clicks loudly off power (giving it its name), effectively giving the truck a front one-way with rear-only braking.  Lock the “clicker” down, and you have full-time four-wheel drive and four-wheel braking.

3-Piece Chassis
Only two screw heads are visible on the underside of the chassis, and all of the components mount to the top of the chassis. Associated calls its new three-piece molded tub chassis a “low CG and low polar moment design.” As the chassis pieces wear, you can replace each section individually.  When assembled, the chassis forms a near glass-smooth bottom surface that will glide over ruts and bumps. The SC10 4×4 is easy to work on. For example, only four screws hold the radio tray in place, with two additional screws capturing the receiver box lid.

Durability Measures
Associated designed the SC10 4×4 from the ground up to handle  abuse. Thick suspension arms, heavy-duty rod ends, 3mm hingepins, and large 32-pitch gears make fore a heavyduty platform. The inner camber-link ball studs pass through the shock tower mounts and thread into metal inserts below. The SC10 4×4 took nearly two years to design and produce; according to designers Kurt Wenger and Jason Corl, they began design in April of 2009.  Each piece was designed by hand in-house and tested in SoCal.

Over-sized Shocks
Large 13mm shocks are used for durability and for a smooth suspension. The shocks may be built pressurized with bladders or emulsion style, and a lower seal cartridge with snap-in limiters allow you to fine-tune without dumping out all of the shock fluid.

Metric Hardware
Associated went with all metric fasteners. The majority of the screws and bolts use a 2.5mm hex-head wrench (others use 2mm). This reduces the number of wrenches needed. Associated also reduced the number of different screw lengths.

Unique dual gearbox drive train coupled together with a 5mm heavy duty belt system with external tension adjustment
> 32-pitch front and rear gearboxes with sealed fluid-filled differentials
> Decoupled center slipper clutch allows for front and rear wheel drive to slip independently, resulting in more traction and stability on bumpy track conditions
> CVAs with captured drive pins and heavy duty 6mm alloy axles
> 12mm hex drive KMC® replica wheels front and rear with aggressive short course racing tires
> Championship short course racing body (clear), with Team Associated decal sheet
> 13mm blue aluminum over-sized threaded shocks with low friction X-ring seals
> Composite modular tub chassis with Low-CG and Low Polar Moment design
> Enclosed water-resistant receiver box, and removable ESC tray for easy clean up and maintenance
> Ball bearing steering system with adjustable steering stops
> All metric hardware and ball bearings throughout
> Uses most 540 and 550 brushless motors

Length: 21.65 in. (550mm)
Width: 11.54 in. (293mm)
Track Width:  9.65 in. (245mm)
Weight: 97.8 oz. (2775g)
Wheelbase: 12.87 in. (327mm)
Internal Gear  Ratio: 2.57:1



Gallery > Team Associated SC10 4×4













1 2 3 4 5
Now Playing: Sliding Servo Mount
Categories: 1 – Main>Daily Picks
Description: Sliding servo mount for the Team Associated SC10 4×4


Sort By: Preset | Name | Date | Rating

1 2 3 4 5


Name: Sliding Servo Mount
Created: 2011-01-31 19:47:16
Categories: 1 – Main>Daily Picks
Description: Sliding servo mount for the Team Associated SC10 4×4

1 2 3 4 5


Name: Team Associated SC10 4×4
Created: 2011-01-31 19:42:10

1 2 3 4 5


Name: Team Associated SC10 4×4 CAD drawing
Created: 2011-01-28 22:45:14
Description: Take an inside look at the Team Associated SC10 4×4.

1 2 3 4 5


Name: Team Associated SC10 4×4 – Clicker
Created: 2011-01-28 21:42:07
Categories: 1 – Main
Description: Check out the new clicker design on the Team Associated SC10 4×4

1 2 3 4 5


Name: Team Associated SC10 4×4
Created: 2011-01-28 21:06:52
Description: Action video and an in depth look at the new Team Associated SC10 4×4 and chassis.
Page: 1 Sort By: Preset | Name | Date | Rating


Bookmark the permalink.

About Mike

Owner of Mike's Hobby

Leave a Reply

Your email address will not be published. Required fields are marked *